Berkel B14-SLC 14" Manual Gravity Feed Meat Slicer, 1/2 HP, Chromium-Plated Knife, 45° Table, 115V
A compact 14" manual gravity feed slicer for deli meats, cheese and other foods on a busy counter.
The Berkel B14-SLC pairs a 14" hollow ground, chromium-plated carbon steel knife with a 1/2 HP motor and a 45° product table that feeds by gravity. The permanent, tapered ring guard covers the non-slicing edge even with the center plate removed, and the slicer comes apart without tools for cleaning. It plugs into a standard 115V grounded outlet with a 5-15P plug.
Set it on a solid, level support in a well-lit work area with room for the product table to travel.
Nominal 14" (350 mm) hollow ground, hardened and polished forged chromium-plated carbon steel knife, turning at 380 rpm.
The full 45° table needs less pressure to feed and uses a removable anodized aluminum pusher to hold product and cut waste.
Infinite thickness adjustment from tissue thin to 5/8" (16 mm) for hard or soft foods.
A two-stone sharpener mounts on top for a lasting, razor-sharp edge.
Removable carriage arm, permanent tapered ring guard with extra room behind the knife, and tool-free disassembly. Finish is stainless steel and sanitary anodized aluminum.
After a power interruption the slicer must be switched on again before the knife restarts.
A grounded 115/120V outlet. The slicer runs on 115V, 60 Hz, single phase and has an attached 6 ft. cord with a NEMA 5-15P plug.
The carriage handles food up to 11" W x 8-1/2" H or 8-1/2" Round.
From tissue thin to 5/8" (16 mm), set with the thickness control knob.
Unplug it, close the gauge plate, then remove the meat pusher, product table, center plate, slice deflector and sharpener without tools. Wash with hot water and a mild detergent, rinse, sanitize and air dry. Berkel advises cleaning at least once a day and not using water jets.
Berkel recommends sharpening at least daily, always on a clean knife, using the built-in two-stone sharpener: 5 to 10 seconds on the sharpening stone, then 2 to 3 seconds on the deburring stone.
Berkel covers parts, labor and travel for one year, excluding wear items such as knives, blades and sharpening stones. Repairs go through Hobart Service or a Designated Berkel Service Location.
Specs
| Manufacturer | Berkel |
|---|---|
| Model Number | B14-SLC |
| Type | Manual Gravity Feed Slicer |
| Net Weight | 74 lb. |
| Shipping Weight | 97 lb. |
| Width | 23 Inches |
| Depth | 26-1/2 Inches |
| Height | 22-1/2 Inches |
| Box Size | 23-1/2" W x 32-1/2" D x 27-3/4" H |
| Voltage | 115 Volts |
| Hertz | 60 Hz |
| Phase | 1 |
| Plug Type | NEMA 5-15P |
| Cord | 6 ft. Flexible 3-Wire, Attached |
| Motor | 1/2 HP, 1-Speed, Totally Enclosed, Permanently Lubricated Ball Bearings, Thermally Protected |
| Knife Diameter | 14" Nominal |
| Knife Material | Hollow Ground, Hardened and Polished Forged Chromium-Plated Carbon Steel |
| Knife Speed | 380 rpm |
| Sharpener | Top-Mounted Two-Stone |
| Knife Guard | Permanent Tapered Ring Guard, Stays on with Center Plate Removed |
| Feed | Full 45° Gravity FeedRemovable Anodized Aluminum Pusher |
| Slice Thickness | Tissue Thin to 5/8 Inch |
| Capacity | 11" Wide x 8-1/2" High or 8-1/2" Diameter |
| Operation | Manual |
| Finish | Stainless Steel and Sanitary Anodized AluminumOne-Piece BaseRemovable Carriage Arm |
| Interlocks | No-Volt Release |
| Control Type | Moisture-Resistant On/Off Switch with Power Light |
| Certifications | NSF, cETLus |
| Sanitation Standard | Complies with NSF/ANSI Standard 8 |
| Warranty | 1 Year Parts, Labor and Travel |
| Warranty Exclusions | Wear Items Excluded |
Certifications
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
