Carter-Hoffmann PH181 Insulated Mobile Heated Holding Cabinet, Bottom Mount Forced-Air Heat System

PH Series Heated Food Transport Cabinets are designed to hold and transport cooked food warm and ready for serving

Why gentle hot air circulation?

Move your feast with heated carts for bulk foods in pans. Great for transport and holding at buffets and remote serving locations.They are constructed of sanitary stainless steel and feature a bottom-mounted lift-out heating system with dial controls and blower heat for even air flow throughout the cabinet. Transport features include wrap-around bumper, wheel-ahead caster pattern and insulated turned-in seam construction.

Carter-Hoffman PH181 Benefits

Flush Mounted Sliding Door Latch

Exclusively designed for transport applications. Door remains closed during transport. Flush design protects latch from damage

Completely Welded Turned-In Seam Construction

Outer cabinet formed and welded to base. All seams turned in the eliminate raw edges. Adds rigidity to entire cabinet.

Heavy-Duty Stainless Steel Base Frame

12 gauge caster bosters with 1”x1” stainless steel perimeter channel supports to withstand heavy loads and harsh transport conditions

Non-Marking Gray Vinly Bumper

Set in heavy-duty 3/16” thick extruded aluminum frame with reinforced corner cut-outs. Protects doorways, walls and cart from damage.

Polyurethane Tread Casters With Sealed

Long lasting, easy rolling for maximum load and minimum maintenance.

High Performance Heater

Blower heating system with side mounted interior heat ducts for fast heat up, recovery and even heat distribution throughout cabinet. Removable without tools for easy maintenance and cleaning

Universal Tray/Pan Slides

Heavy-duty stainless steel slides are adjustable on 1- 3/4” centers (standard spacing at 3-1/2”. Accommodate 12”x20” steam table pans, 18”x26” sheet pans, 1/1 and 2/1 gastronorm pans, and 20”x20” glass racks

Offset "Wheel Ahead" Pattern

Only one wheel can pass over uneven surfaces at a time for easy handling and steering.

Technical Information

Casters

PH181, PH1810, PH1830, PH1860: 5” & 6” diameter polyurethane tread. All swivel on PH185, PH181, PH1820 and PH1830. Two swivel and two rigid on PH1860. Sealed roller bearing and double ball bearing swivel. Zerk grease fittings. Plated mounted and bolted to base in offset wheel-ahead pattern. Two casters fitted with brakes

Construction

Completely welded cabinet construction and top corners, with outer cabinet formed to base and welded. All seams turned in to eliminate raw edges

Base Frame

12 gauge stainless steel full depth bolsters with 1”x1” 14 gauge stainless steel perimeter tube supports welded to bolsters

Cabinet Material

All stainless steel construction; 20 gauge polished exterior and 24 gauge interior.

Heating System

Bottom-mounted, all stainless steel construction. Removable without tools.1600 watt inconel-sheathed heating element. High impedence protected, internally cooled fan motor. Full range thermostat, remote sensing bulb & power indicating light

Tray Rack Assemblies

16 gauge universal slides, fully adjustable at 1 3/4” spacing, placed into 18 gauge stainless steel rack post. Standard spacing at 3 1/2”.

Doors

Double panel welded stainless steel with heavy-duty vinyl gasket. 20 gauge polished exterior and 24gauge interior. Filled with 1” thick high density fiberglass insulation

Latch

Flush mounted heavy-duty sliding latch for positive closing of door. Easy grip handle bolted to door

Thermometer

Dial type with remote sensing bulb. Located on side of cabinet. Protected by lexan thermometer cover.

Performance

Capable of heating to 200O F (94O C). Preheat to 160O F (71O C) in approximately 25 minutes.

Insulation

High density fiberglass, full 1” thick continuous wrap-around type insulation

Hinges

Concealed, stainless steel hinge with 5/15” pin. 180 degree door swing

Electrical Characteristics

Operates on 120 volts, 60 cycle, single phase, 1650 watts, 13.7 amps. Ten foot 3 wire rubber cord with 3 prong grounding plug. NEMA 5-15P.