Hatco GRAH-132D3 Glo-Ray 132" Dual High Watt Aluminum Infrared Strip Heater, 3" Spacer, 15" Deep, 6240 W, 208/240V
Description
Two high watt infrared heaters in one 132" housing keep a deep pass-through or a row of plated food hot and ready to serve.
The Hatco GRAH-132D3 is a Glo-Ray dual high watt aluminum infrared strip heater, 132" wide and 15" deep. Two 6" heater sections sit side by side with a 3" spacer for a deeper holding area, and the pre-focused heat pattern covers the whole surface with no cold spots. It draws 6240 watts on 208V or 240V single phase and uses tandem end-to-end elements; Hatco offers it with a remote control box (RMB) or remote switch only.
Will it fit · Will it hook up
- Outside size
- 132" W x 15" D x 2.5" H
- Where it works
- Hatco recommends dual units for a 20" to 24" deep pass-through
- Power
- Single phase, 6240 W: 30.0 A at 208V, 26.0 A at 240V; set the voltage at order
- Hookup
- 3 ft. conduit with leads at the server's right, hardwired by an electrician; Hatco lists the conduit as standard on 120V and 208V models
- Mounting height
- Hatco recommends 14" to 18" above the food for high watt dual units
- Clearance
- Not for combustible surroundings. With remote switches: 8" to the surface below, 3" to a wall, can be flush to an overshelf
The size number is the overall length: the GRAH-132D3 is 132" wide, so measure the shelf or pass-through for that.
No cold spots
A pre-focused heat pattern covers the entire holding surface, so food holds at serving temperature without drying out or cooking further.
Deeper holding area
A 3" spacer joins two 6" heater sections for a 15" deep unit that covers a deeper pass-through.
High watt output
6240 watts from metal-sheathed tubular elements for mounting 14" to 18" above the food.
Housing that stays straight
The continuous extruded aluminum housing does not sag across the full 132" width, and the reflector does not blacken, so the heat pattern stays even.
Tandem elements
End-to-end elements may be individually controlled. Order a Hatco remote control box (RMB) or remote switch with the heater.
Guarded and insulated
Reinforced wire guards protect the element without blocking heat, and insulation minimizes heat loss.
Delivery and setup
- Inspect the carton for damage before you sign, and note any damage on the delivery receipt.
- Approximate shipping weight is 73 lb, including packaging; a remote control box is not included.
- Have a qualified electrician hardwire it to a properly grounded circuit that matches the voltage on the specification label.
- Install remote control boxes and switches outside the heat zone, or heat will damage them.
- Dual units cannot be installed in combustible surroundings, and Hatco does not allow a decorative soffit around a pass-through heater.
- Clean daily once cool: wipe with a damp, non-abrasive cloth and dry. Do not submerge, steam clean or spray it.
Questions buyers ask
How high should I mount it?
Hatco recommends 14" to 18" above the food for high watt dual units. With remote switches, keep at least 8" to the surface below.
What power does it need?
Single phase at 208 or 240V, chosen at order. At 6240 watts it draws 30.0 A at 208V, 26.0 A at 240V. It is hardwired through conduit with leads.
Does it come with a switch?
No. Hatco offers this size with a remote control box (RMB) or remote switch only, ordered separately. Its tandem elements may be individually controlled.
Single or dual strip heater?
Hatco recommends a single unit for a 12" to 16" deep pass-through and a dual unit for a 20" to 24" deep pass-through.
Can I order colors or sneeze guards?
Yes, at time of purchase only: Designer colors or gloss finishes, sneeze guards, an indicator light, remote switches and stands. Non-standard colors are non-returnable.
What certifications does it have?
The Hatco spec sheet shows cULus and NSF marks, and Made in USA.
What is the warranty?
Hatco covers the metal-sheathed element for 1 year parts and labor plus 1 more year parts-only, and other parts for 18 months from shipment or registration, whichever is later. Register within 90 days of shipment.
Specs
| Manufacturer | Hatco |
|---|---|
| Model Number | GRAH-132D3 |
| Series | Glo-Ray Aluminum Dual Infrared Strip Heater, GRAH-D High Watt |
| Shipping Weight | 73 lb. |
| Width | 132 Inches |
| Depth | 15 Inches |
| Height | 2.5 Inches |
| Spacer | 3 Inch Spacer Between Two 6 Inch Heater Sections |
| Voltage | 208 or 240 Volts |
| Wattage | 6240 Watts |
| Amps by Voltage | 208V: 30.0 Amps240V: 26.0 Amps |
| Phase | Single Phase |
| Connection | Hardwired, 3 ft. Conduit with Leads, Server's RightConduit Standard on 120V and 208V Models |
| Control | Remote Control Box RMB or Remote Switch Only, Ordered Separately |
| Element Layout | Tandem End-to-End Elements, May Be Individually Controlled |
| Element | Metal-Sheathed Tubular Infrared Elements |
| Recommended Mounting Height | 14 to 18 Inches, High Watt Dual |
| Clearances | Not for Combustible SurroundingsBuilt-In Switches: 10 Inches to Surface Below, Pass-Through Only, 1 Inch Below OvershelfRemote Switches: 8 Inches to Surface Below, 3 Inches to Wall, Flush to Overshelf |
| Housing | Extruded Aluminum, Clear Anodized Finish Standard |
| Mounting | Four Stainless Steel Shelf Mounting Tabs |
| Factory Options | Designer Color or Gloss FinishIndicator Light, Remote OnlyExtended LeadsSneeze Guards 9.375 or 14 InchRemote Infinite or Toggle SwitchesRemote Box RMBTubular Stands |
| Accessories | Adjustable Angle Brackets 1 to 2 InchChain Suspension |
| Certifications | cULus, NSF |
| Country of Origin | Made in USA |
| Warranty | 18 Months Limited |
| Warranty Details | Metal-sheathed element: 1 year parts and labor plus 1 more year parts-onlyOther parts: 18 months from shipment or registration, whichever is laterRegister within 90 days of shipment24/7 parts and service help in US and Canada |
Certifications
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
What Our Customers Say

