Hatco GRAH-48D3-120-QS Glo-Ray 48" Dual High Watt Aluminum Infrared Strip Heater, 3" Spacer, 15" Deep, 2200 W, Toggle Switch, 120V, Quick-Ship
Description
Two high watt infrared heaters in one 48" housing keep a deep pass-through or a row of plated food hot and ready to serve.
The Hatco GRAH-48D3-120-QS is a Glo-Ray dual high watt aluminum infrared strip heater, 48" wide and 15" deep. Two 6" heater sections sit side by side with a 3" spacer for a deeper holding area, and the pre-focused heat pattern covers the whole surface with no cold spots. This Hatco Quick-Ship stock item (GRAH48D120V) is wired for 120V single phase, 2200 watts, with a built-in toggle switch and conduit with leads.
Will it fit · Will it hook up
- Outside size
- 48" W x 15" D x 2.5" H
- Where it works
- Hatco recommends dual units for a 20" to 24" deep pass-through
- Power
- 120V single phase, 2200 W, 18.3 A
- Hookup
- 3 ft. conduit with leads at the server's right, hardwired by an electrician
- Mounting height
- Hatco recommends 14" to 18" above the food for high watt dual units
- Clearance
- Not for combustible surroundings. Built-in switches: 10" to the surface below, pass-through only, 1" below an overshelf
The size number is the overall length: the GRAH-48D3-120-QS is 48" wide, so measure the shelf or pass-through for that.
No cold spots
A pre-focused heat pattern covers the entire holding surface, so food holds at serving temperature without drying out or cooking further.
Deeper holding area
A 3" spacer joins two 6" heater sections for a 15" deep unit that covers a deeper pass-through.
High watt output
2200 watts from metal-sheathed tubular elements for mounting 14" to 18" above the food.
Housing that stays straight
The continuous extruded aluminum housing does not sag across the full 48" width, and the reflector does not blacken, so the heat pattern stays even.
Toggle switch control
Toggle switch control at the chef's left side is standard. Hatco toggle switches are rated 15 amps maximum, and 120V dual models may need additional switches.
Guarded and insulated
Reinforced wire guards protect the element without blocking heat, and insulation minimizes heat loss.
Delivery and setup
- Inspect the carton for damage before you sign, and note any damage on the delivery receipt.
- Approximate shipping weight is 27 lb, including packaging; a remote control box is not included.
- Have a qualified electrician hardwire it to a properly grounded circuit that matches the voltage on the specification label.
- Install remote control boxes and switches outside the heat zone, or heat will damage them.
- Dual units cannot be installed in combustible surroundings, and Hatco does not allow a decorative soffit around a pass-through heater.
- Clean daily once cool: wipe with a damp, non-abrasive cloth and dry. Do not submerge, steam clean or spray it.
Questions buyers ask
How high should I mount it?
Hatco recommends 14" to 18" above the food for high watt dual units. With built-in switches, keep at least 10" to the surface below; with remote switches, 8".
What power does it need?
120V single phase. It draws 2200 watts, 18.3 amps, and is hardwired through conduit with leads; there is no plug.
Will one switch handle 120V?
Hatco notes that 120V dual models may need additional switches, depending on the unit and wattage. Confirm the 120V control setup with Hatco when you order.
Single or dual strip heater?
Hatco recommends a single unit for a 12" to 16" deep pass-through and a dual unit for a 20" to 24" deep pass-through.
What certifications does it have?
The Hatco spec sheet shows cULus and NSF marks, and Made in USA.
What is the warranty?
Hatco covers the metal-sheathed element for 1 year parts and labor plus 1 more year parts-only, and other parts for 18 months from shipment or registration, whichever is later. Register within 90 days of shipment.
Specs
| Manufacturer | Hatco |
|---|---|
| Model Number | GRAH-48D3-120-QS |
| Hatco Item Number | GRAH48D120V |
| Program | Hatco Quick-Ship Stock Item |
| Series | Glo-Ray Aluminum Dual Infrared Strip Heater, GRAH-D High Watt |
| Shipping Weight | 27 lb. |
| Width | 48 Inches |
| Depth | 15 Inches |
| Height | 2.5 Inches |
| Spacer | 3 Inch Spacer Between Two 6 Inch Heater Sections |
| Voltage | 120 Volts |
| Wattage | 2200 Watts |
| Amps | 18.3 Amps |
| Phase | Single Phase |
| Connection | Hardwired, 3 ft. Conduit with Leads, Server's Right |
| Control | Built-In Toggle Switch Control, Chef's Left SideToggle Switch Rating Max. 15 Amps |
| Control Notes | 100V and 120V Models May Require Additional SwitchesInfinite Switches Remote Only, Max. 12.2 Amps |
| Element | Metal-Sheathed Tubular Infrared Elements |
| Recommended Mounting Height | 14 to 18 Inches, High Watt Dual |
| Clearances | Not for Combustible SurroundingsBuilt-In Switches: 10 Inches to Surface Below, Pass-Through Only, 1 Inch Below OvershelfRemote Switches: 8 Inches to Surface Below, 3 Inches to Wall, Flush to Overshelf |
| Housing | Extruded Aluminum, Clear Anodized Finish Standard |
| Mounting | Four Stainless Steel Shelf Mounting Tabs |
| Accessories | QSANGLE-D Adjustable Angle Brackets, 2 Pairs |
| Certifications | cULus, NSF |
| Country of Origin | Made in USA |
| Warranty | 18 Months Limited |
| Warranty Details | Metal-sheathed element: 1 year parts and labor plus 1 more year parts-onlyOther parts: 18 months from shipment or registration, whichever is laterRegister within 90 days of shipment24/7 parts and service help in US and Canada |
Certifications
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
What Our Customers Say

